Central Heating Wiring & Controls Book 3
![](https://mrcombi.com/wp-content/uploads/2024/07/23-07-Wiring-Cover-1-722x1024.jpg)
What’s inside:
- Schematics 23
- Fault finding 55
- 2 Zone S Plan 51
- Wiring Centres 14
- Frost Protection 54
- SMART Controls 46
- 3 Zone S Plan Plus 25
- Programmer wiring 35
- Mid Position Y Plan 15
- Testing components 57
- Diagrams in full colour 22
- Fault Finding flow charts 10
![](https://mrcombi.com/wp-content/uploads/2024/08/3.books-1.jpg)
The aim of this book is to make wiring more rewarding. It had been design to help you carry out installations and fault finding on control circuits by giving you all the information you need in a clear and logical manner.
The most common control circuits in use in the UK are the three port (Mid Position) and two and three port zone circuits. This book therefore contains a greater number of diagrams for those circuits.
For many years electricians and heating engineers have commented that wiring heating controls is a difficult subject to learn. (This book is easy to follow).
They want to be able to wire and test these circuits with confidence but the existing diagrams are not always easy to follow.
This book is for all levels from basic to advance easy to follow.
Don’t leave home without this book.
![](https://mrcombi.com/wp-content/uploads/2024/08/3.books-4.jpg)
![](https://mrcombi.com/wp-content/uploads/2018/02/BoW-Honeywell-Frost3.png)
Central Heating Fault Finding Book
![](https://mrcombi.com/wp-content/uploads/2024/07/22-12-Central-Heating-Fault-Finding-hi-res-724x1024.jpg)
Written by a breakdown engineer of 45 years, George Staszak is the man who started Mr Combi Training ‘Hands On’ fault finding and wiring course for over 20 years until retiring in September 2022.
If you are an engineer going to service or repair a boiler you take tools, spanners, screwdrivers etc do you tak a manual? No, don’t expect one to be there, problem.
Don’t waste time guessing or phoning a friend, this book has 99% of every fault known. Use the flow charts.
Don’t go to any boiler without this book, no manual? No problem!
In our Central Heating Writing & Controls Book you’ll find a vast array of information and diagrams.
What’s included:
- By Pass 42
- Gas valve 31
- Fan testing 66
- Polarity test 16
- PCB testing 36
- Pump testing 38
- Pumping over 41
- Boilers in lofts 45
- Short circuit test 14
- Factory flow charts 8
- 16 Popular faults 28
- Plate to plate faults 43
- Sequence of wiring 24
- Diverter valve faults 46
- Sequence of operation 25
- All about expansion vessels 72
- Fault isolation (what blows fuses) 22
![](https://mrcombi.com/wp-content/uploads/2024/07/Central-Heating-Fault-Finding-low-res-Book-dragged.jpg)
![](https://mrcombi.com/wp-content/uploads/2024/07/Chart-1v-copy-1.png)
Every year all gas boilers should be checked for safety and efficiency by a Register Gas Installer with Gas Safe, often not done because there are not enough of them.
If the boiler is still under guarantee which could be up to 12 years, this check is part of the T&Cs.
Our CO CO2 chart will show you how good or bad THE boiler is, the result could be do nothing, service or time to replace. Every gas installer should have this chart.
Easy to follow and accurate.
£5.00 no vat.
Available to UK Post Codes only.
Click below to order